Autowatch Ghost Immobiliser Installation
The Ghost is the UK’s most advanced aftermarket immobiliser that works with CAN buses. It is discrete, does not use LED indicators or key fobs and is concealed in the vehicle's wiring.
It also permits the user to temporarily disable the system by using Transport Mode in the event of renting out their vehicle. This guide will guide you through the installation of a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a cutting-edge security device that protects your vehicle from hacking, key cloning and relay attacks. The system is linked directly to the ECU of your vehicle and secured by a PIN code you set. It's inaccessible to thieves using diagnostic scanners or other advanced methods, and it is unable to be disabled by cutting circuits.
The system is simple to use, however professional installation is recommended to ensure a clean connection to the ECU of your vehicle. Installers who are approved by Thatcham can assist you with the installation and programing of your Ghost system. They can also recommend a tracking system or alarm to complement the protection package for your vehicle.
The first step is to disconnect the battery to prevent accidental airbag deployment or short circuits. After the battery has been disconnected, the installer can start working safely. Hand tools are the most basic to be used to make precise connections. A multimeter is useful to test electrical values. Cable ties and insulation tape are also vital for protecting connections and keeping wiring neat. The Ghost Immobiliser user's manual will give specific instructions that are specific to your particular model.
It is essential to choose a grounding location that is free of dirt or paint during installation. Installers must also ensure that the immobiliser's wires CAN H and the CAN L are connected to the appropriate ECU ports. Depending on the model, these wires might require soldering or plugged in. A high-quality connector is recommended to ensure a sturdy and secure connection.
Transport Mode can be turned on by the customer after the installation is complete. This allows the vehicle to be utilized by valet parking companies or mechanics without needing to know the pin code. The customer has to press the icon for service on the dashboard five times in two seconds. After this is done the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 immobiliser is TASSA certified and is an extremely efficient immobiliser. It's a great choice for those who rent their vehicles often through platforms like Turo. An immobiliser can cut down on the cost of insurance, as it lowers the chance of theft.
Getting Started
If you are looking for a solution that will protect your vehicle from thieves You can't go wrong with an autowatch ghost immobiliser. It will stop your car from starting even when a criminal steals or copies the key. It's possible due to its advanced technology that prevents the engine from starting until the right PIN code is entered.
The device works by connecting to the CAN bus network of your vehicle which allows it to communicate with the ECU directly. It uses existing buttons on the dashboard and steering wheel to create a unique sequence only you know and makes it impossible for anyone else to start your car. This is the ultimate system to safeguard your pride and joy. It will ensure that your car's value remains intact if you ever want to sell it.
Installing a Ghost immobiliser is easy however, you must follow the instructions to avoid electrical issues and system malfunctions. First, you must locate and identify a constant 12V power source and an appropriate grounding point on the vehicle's chassis. After that, you are able to begin to connect the wires to the immobiliser. Use high-quality connectors, and soldering techniques for an effective connection. Make sure to shield the connections with heat shrink tubing or insulation tape, as well as other materials to avoid electrical short circuits.
Once the wires are connected, you are able to reconnect the battery and turn on the engine to test the immobiliser's functionality. If everything is functioning properly, you can install it in a secure location beneath the dash or anywhere else in the vehicle. Make sure you hide it well to prevent thieves from getting into it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified this means it complies with the highest standards of security and is an excellent protection against car thieves. It is resistant to key cloning and hacking and is not able to be disabled without the code. The device is also easy to use and can be set into the service valet mode to ensure that your automobile is not activated when you bring it in for servicing or an MOT.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to stop theft of vehicles. It is directly connected to the vehicle's CAN bus and communicates with the ECU which makes it virtually undetectable as an addition to your car. In autowatch ghost 2 immobiliser to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings for your vehicle.
It's also totally undetectable by thieves using diagnostic scanners. The system doesn't send or receive radio frequency signals but instead uses CAN data to communication with your ECU. In addition, it doesn't need any modification to your car's existing key fobs.
To use the Ghost Immobiliser, simply switch on the ignition in your car and then enter the sequence to disarm (either one or two buttons). The indicator will flash twice to confirm that you've entered the correct code. Now you can begin driving your car in a safe manner.
Once installed Once installed, the Ghost Immobiliser will safeguard your vehicle from key cloning and hacking and will also protect the value of your pride and joy. In Transport Mode, you can temporarily disable the Ghost Immobiliser if you need to hand your car over for service or valet parking.
You'll require a continuous power source (12V) as well as an earthing point to complete the installation of the Ghost immobiliser. Make sure both are well-insulated and can be touched. Cable ties are also recommended for bundling and secure the wires. This will reduce the risk of theft by potential thieves. Be sure to check the exact locations of these points to avoid making mistakes, and mark them with an adhesive or label. Check all connections for signs they're getting worn out. Make sure all connections are in place, and are properly sealed. Don't forget to test your Ghost Immobiliser after installation has been completed. This will make sure that the unit is functioning properly and that all connections are secure and insulated. If there are any issues, make sure to address them immediately.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that integrates seamlessly with your car's ECU in order to prevent the motor from starting without authorization. Its innovative technology protects your vehicle from key cloning and hacking and other methods that thieves employ to steal vehicles. The Ghost also works in tandem with other alarm and tracking systems to give the most complete protection for your vehicle. The Ghost's unparalleled features and subtle design make it a preferred choice for car lovers and security-conscious motorists alike.
It is essential to follow the steps of installation in order to ensure a proper integration of Ghost Immobiliser. Consult the wiring diagram of the vehicle as it will aid you in locating and connecting the wires. You'll need to determine the grounding and power sources. Once these are found, you'll need to mark them so that they're easily identifiable when installing. It is essential to use top-quality materials and tools. Basic hand tools will help you make precise connections. A multimeter can verify electrical values and guarantee security. Cable ties and insulation tape will help keep all connections tidy and neat. Additionally, a user's manual will provide specific guidance tailored to your Ghost model.
Before proceeding with the installation it is important to test the system by entering the PIN code, then starting the vehicle. This test will verify that the immobiliser is working in the way it was intended, preventing unauthorized vehicle start-ups. This step should be performed regularly as part your regular inspections of the vehicle to ensure that the system is always functioning properly.
Once the installation is complete, you can drive your vehicle with confidence. The Ghost will protect your pride and joy from would-be car thieves. It will ensure that no one is able to take your car away without having the correct PIN code. The Ghost can be paired with an approved Thatcham tracker, which detects attempts at theft or tampering. This allows you to track your car in the event that it's stolen.
The Ghost is compatible with a wide variety of vehicles, including those made by most major manufacturers. Monty's Locksmith can assist you in securing your vehicle with this cutting edge device. Contact us today to find out more about our services and installation options. We are a TASSA Installer who is registered which guarantees that we adhere to strict standards and procedures for installing our products. This ensures customers as well as insurance companies and law enforcement agencies that all installations are carried out safely and correctly.